# See what the air is doing inside the horn

> How to read horn particle velocity, pressure, acoustic impedance and radiating outputs in 00 Simulator, with figures from the tapped and back-loaded horn examples.

Source: https://simulator.00aud.io/docs/horns/diagnostics

A smooth SPL curve can hide a lot: air moving fast through a narrow section, a pressure peak at a closed end, or two outputs cancelling. The four horn diagnostic graphs read the path at any station you pick and split the sound into each thing that radiates.

## Open them

Add them from **Add tile**: **Horn Particle Velocity**, **Horn Pressure**, **Horn Acoustic Impedance** and **Horn Radiating Outputs**. They show horn enclosures only.

## The four graphs

| Graph | Unit | What it shows |
| --- | --- | --- |
| **Horn Particle Velocity** | m/s, peak | How fast the air moves at the chosen location: the volume flow divided by the area there. It is not the cone’s speed, and it is not a sum over outputs. |
| **Horn Pressure** | Pa, RMS, or phase in degrees | The sound pressure inside the path at the chosen location. Switch between **Magnitude** and **Phase**. |
| **Horn Acoustic Impedance** | Pa·s/m³ | Pressure divided by volume flow at the location, as **Magnitude**, **Phase**, **Resistance** or **Reactance**. It is acoustic, not the electrical impedance in ohms. Where no air flows, it is undefined and left out. |
| **Horn Radiating Outputs** | dB, or phase in degrees | Each mouth, port and exposed cone on its own, dashed, with their coherent total solid. The outputs add as pressures with their phase, so their dB values do not simply add. |

## Pick a location

Velocity, pressure and impedance read one location at a time. Locations are named by path, span and end, such as _Main H1 throat_, with their position and area. Where a driver enters or a branch joins partway along a span, the two sides are separate locations, marked toward the throat and toward the mouth. Pressure is continuous across the join, but the flow on each side can differ.

## An example: the tapped horn

_Interactive walkthrough in the page: the simulator's own tiles running a short demo._

The tapped horn example at 100 W in half space. The air moves faster at the constriction, the narrowest station between the closed end and the mouth, than at the mouth itself; a narrow section like this is where to check for noise first. Pressure is highest at the closed end, because the air cannot move there. [The tapped horn](https://simulator.00aud.io/docs/horns/tapped-horn).

## Outputs that add and cancel

Where a design radiates from more than one place, **Horn Radiating Outputs** shows each one. In a back-loaded horn the front of the cone and the horn mouth both radiate, and the total depends on how they line up in phase.

_Figure: Back-loaded horn, horn length 1.2 m: the coherent total, solid, and each radiating output on its own, dashed: main mouth and direct radiator._

The outputs are pressures, so they add with their phase: where the dashed lines are close in level and opposite in phase, the total drops below both.

Back-loaded horn, horn length 1.2 m. Solid: the total. Dashed: Main mouth and Direct radiator on their own.

[The back-loaded horn](https://simulator.00aud.io/docs/horns/back-loaded-horn) · [The compound horn](https://simulator.00aud.io/docs/horns/compound-horn), which has two mouths.

## What they are not

- They are linear. They do not predict turbulence, distortion or compression, and no air-speed warning is applied the way the port velocity check is for a box. Decide your own limit for the air speed in a narrow section.
- A location missing from a comparison enclosure is left out, not drawn at zero.
- Max SPL, excursion and impedance still apply to horns. Max SPL is the lower of two ceilings, the cone reaching Xmax and the driver’s thermal limit, with the thermal rule chosen in the tile’s settings. The default is real input power, the rule Hornresp uses. [Max SPL](https://simulator.00aud.io/docs/reference/tiles/max-spl).
- The dashed folded line from the **Fold** tile is not drawn on these four graphs.

Every graph, unit and display mode in detail: [Horn Particle Velocity](https://simulator.00aud.io/docs/reference/tiles/horn-particle-velocity), [Horn Pressure](https://simulator.00aud.io/docs/reference/tiles/horn-pressure), [Horn Acoustic Impedance](https://simulator.00aud.io/docs/reference/tiles/horn-acoustic-impedance), [Horn Radiating Outputs](https://simulator.00aud.io/docs/reference/tiles/horn-radiating-outputs).

## Ask your AI

**Ask your AI**

Your assistant runs the same solver on your own designs through the 00 Simulator connector.

> Using 00 Simulator, simulate my horn at the power it is set to and read its horn diagnostics. Where along the path is the particle velocity highest, how high does it get and at what frequency? Then tell me whether any outputs cancel inside the working band.
